It is currently Sat Nov 28, 2020 4:46 pm

All times are UTC


THE PROP DEN is primarily a Darth Vader Prop Discussion Board, but we also deal with other Star Wars Props as well as Prop Replicas from other movies. If you do not yet have an account, set one up, sign in and jump into the Vader Prop Discussions!


Post new topic Reply to topic  [ 592 posts ]  Go to page Previous  1 ... 36, 37, 38, 39, 40
Author Enter your Message here
 Post subject: Re: 1:6 Darth Vader 3D Laser Scan & Print Project
PostPosted: Sun Oct 04, 2020 11:04 am 
Site Admin
User avatar

Joined: Thu Aug 31, 2006 8:58 am
Posts: 10747
Location: Denmark
Interest list has started. We currently have full 3 ANH sets ready and more to come. Working on getting ESB done as well, and will make RotJ kits pr order.

interest-16-laser-scanned-darth-vader-armor-kits-run-vt5379.html

Image, on Flickr
(click the picture to go to the larger version. Will post more pictures in the WIP thread.)

Not clickable pictures:
Image, on Flickr
Image, on Flickr
Image, on Flickr
Image, on Flickr


Top
 Profile  
 
 Post subject: Re: 1:6 Darth Vader 3D Laser Scan & Print Project
PostPosted: Thu Oct 08, 2020 1:45 pm 
Site Admin
User avatar

Joined: Thu Aug 31, 2006 8:58 am
Posts: 10747
Location: Denmark
Compared to Kaiyodo. I only have early v2 helmets, as the new stuff was sent to Paul, which may be a fraction larger. Please note that this is an old ANH dome, so it is taller, but slimmer at the crown section, while flaring out too much at the bottom skirt sides. The new domes are correctly shaped.

Image, on Flickr
Image, on Flickr
Image, on Flickr
Image, on Flickr


Top
 Profile  
 
 Post subject: Re: 1:6 Darth Vader 3D Laser Scan & Print Project
PostPosted: Fri Nov 06, 2020 11:55 am 
Site Admin
User avatar

Joined: Thu Aug 31, 2006 8:58 am
Posts: 10747
Location: Denmark
This is to show how the face mask casts are done. They are done as a solid shell, but you can cut it open with a dremel and slowly clean away the material at the lenses and mouth area if you want to insert lenses and grills. There may be small support structures inside, but they should be easily removed.

The pictures below illustrate it done quickly on a test print.

Image, on Flickr
Image, on Flickr
Image, on Flickr
Image, on Flickr


Top
 Profile  
 
 Post subject: Re: 1:6 Darth Vader 3D Laser Scan & Print Project
PostPosted: Fri Nov 06, 2020 5:07 pm 
User avatar

Joined: Wed Apr 18, 2007 6:21 am
Posts: 703
Location: Colorado Springs, Colorado
Excellent photos! I was wondering how it was going to work replacing the chin screen. Now I'm mulling over how to connect the helmet to the neck joint.

Cannot wait to see these in hand!

Dave


Top
 Profile  
 
 Post subject: Re: 1:6 Darth Vader 3D Laser Scan & Print Project
PostPosted: Sat Nov 07, 2020 12:41 pm 
Site Admin
User avatar

Joined: Thu Aug 31, 2006 8:58 am
Posts: 10747
Location: Denmark
Well, you can just leave the filler bit at the neck and only trim out the back. However, I would probably recommend trimming out the whole thing, so you can actually get access to the mouth and chin vent area. I remember how it was when I did that to the v1 master and it takes an awful lot of time to grind down the area slowly, but it is doable with jewelers files. Then you can use something like Aves Apoxie Sculpt to rebuild the neck. If it requires a harder material for the actual peg insertion, you can use something else just for that and fill around it with apoxie sculpt.


Top
 Profile  
 
 Post subject: Re: 1:6 Darth Vader 3D Laser Scan & Print Project
PostPosted: Thu Nov 12, 2020 12:55 am 
Site Admin
User avatar

Joined: Thu Aug 31, 2006 8:58 am
Posts: 10747
Location: Denmark
Working on Prowse. Trying to finish the hair, so I can have it fused to the face model. First time I've tried to sculpt hair digitally, so I'm open to suggestions regarding improvement.

Image, on Flickr
Image, on Flickr
Image, on Flickr
Image, on Flickr
Image, on Flickr
Image, on Flickr
Image, on Flickr
Image, on Flickr


Top
 Profile  
 
 Post subject: Re: 1:6 Darth Vader 3D Laser Scan & Print Project
PostPosted: Thu Nov 12, 2020 12:04 pm 
User avatar

Joined: Thu Jan 03, 2019 8:49 am
Posts: 117
Location: Aosta Valley, Italy
No Humor Man wrote:
Interest list has started. We currently have full 3 ANH sets ready and more to come. Working on getting ESB done as well, and will make RotJ kits pr order.

interest-16-laser-scanned-darth-vader-armor-kits-run-vt5379.html

Image, on Flickr
(click the picture to go to the larger version. Will post more pictures in the WIP thread.)

Not clickable pictures:
Image, on Flickr
Image, on Flickr
Image, on Flickr
Image, on Flickr


Wow I missed this, they really look like quality pieces! Good job!


Top
 Profile E-mail  
 
Display posts from previous:  Sort by  
Post new topic Reply to topic  [ 592 posts ]  Go to page Previous  1 ... 36, 37, 38, 39, 40

All times are UTC


You cannot post new topics in this forum
You cannot reply to topics in this forum
You cannot edit your posts in this forum
You cannot delete your posts in this forum
You cannot post attachments in this forum

Jump to:  
Blue Moon by Trent © 2007
Powered by phpBB © 2000, 2002, 2005, 2007 phpBB Group
Hosted by Freeforum.ca, get your free forum now! TOS | Support Forums | Report a violation
buy web visitors
MultiForums powered by echoPHP phpBB MultiForums