It is currently Thu Mar 28, 2024 8:14 pm

All times are UTC


THE PROP DEN is primarily a Darth Vader Prop Discussion Board, but we also deal with other Star Wars Props as well as Prop Replicas from other movies. If you do not yet have an account, set one up, sign in and jump into the Vader Prop Discussions!


Post new topic Reply to topic  [ 3 posts ] 
Author Enter your Message here
 Post subject: Setting a semi-permanent Vader mount using Instamorph
PostPosted: Mon Mar 02, 2015 7:40 pm 
Offline
User avatar

Joined: Mon Mar 10, 2014 5:26 pm
Posts: 644
Location: Dallas, TX, USA
Many of the latest licensed and fan-made Vader helmets available today incorporated improved mount designs which make use of magnets to keep the mask and dome secured in a fixed position (e.g. those from eFx, AVONOS, jarenMCL).

But for the Rubies, DPCA, and DPDLX owners, the floppy and wobbly mount is quite familiar. The basic issues are 1) the perimeter shape of the tube at the top of the mask does not match the contour of the dome; and 2) the excess space between the mask and dome attachments.

I needed to sand down both the tube and the ring on my DPDLX to more accurate positioning, but there was still a bit of wobble, and it was clear I wouldn't be able to get a secure fit with the mount alone without filling in these spaces:

Image

I didn't want to use epoxy of other permanent method of filling and sealing the mount; instead I tried using Instamorph which yielded good results. Instamorph does not adhere to painted fiberglass (but does to ABS plastic FYI). So Instamorph would be a good choice for filling in these spaces and to provide any fine-tuning to the mount positioning. It's moldable at around 140 degrees F, and is fairly solid after a few minutes of cooling.

So starting with a clump of instamorph dropped into 150 degree F water:

Image

I spread it along the front of the dome ring:

Image

And then slowly joined the mask to the dome, stopping when I got to the desired mount height and position. I held it in place until the Instamorph cooled.

Image

What resulted was something that looks like a removable denture:

Image

Image

Incidentally, you could make 2 of these if you wanted to easily switch between an ESB or ROTJ mount height.

For a secure mount, you can spread the Instamorph around and under the dome ring and around and over the mask tube to create a mechanical (not an adhesive) attachment. This also evens out the pressure across more of the connection rather than impinging on specific stress points.

Image

And yes, this is strong enough of a connection to allow tricks like this:

Image

I was able to remove all previous methods of supplementing the factory mount using foam padding, velcro, etc. at the forehead and the sides. Now I only have the mount keeping the mask and dome separating in place:

Image

I wanted to share this tip as I found it's a good solution to adjust and/or secure a wobbly mount. Plus, if you ever want to change it, just soak a cloth in hot water and apply it to the installed Instamorph for a minute or two, and it loosen to be removed and reused.


Top
 Profile E-mail  
 
 Post subject: Re: Setting a semi-permanent Vader mount using Instamorph
PostPosted: Wed Mar 04, 2015 7:45 am 
Offline
User avatar

Joined: Thu Dec 21, 2006 10:46 pm
Posts: 5241
Location: San Jose, CA
Bravo!

_________________
Cordially,

- Mac
( Follow me on Facebook: https://www.facebook.com/sculptingvader/ )


Top
 Profile  
 
 Post subject: Re: Setting a semi-permanent Vader mount using Instamorph
PostPosted: Mon Mar 09, 2015 5:35 pm 
Offline
User avatar

Joined: Mon Mar 10, 2014 5:26 pm
Posts: 644
Location: Dallas, TX, USA
Thank you sir!


Top
 Profile E-mail  
 
Display posts from previous:  Sort by  
Post new topic Reply to topic  [ 3 posts ] 

All times are UTC


Who is online

Users browsing this forum: No registered users and 1 guest


You cannot post new topics in this forum
You cannot reply to topics in this forum
You cannot edit your posts in this forum
You cannot delete your posts in this forum
You cannot post attachments in this forum

Jump to:  
cron
Blue Moon by Trent © 2007
Powered by phpBB © 2000, 2002, 2005, 2007 phpBB Group
Hosted by Freeforum.ca, get your free forum now! TOS | Support Forums | Report a violation
MultiForums powered by echoPHP phpBB MultiForums